Electrical, mechanical and plumbing, wherever your project is +1 407-751-1755WhatsAppTeams callLinkedIninfo@mep.symateq.com
Hotel lobby with timber slats and cove lighting
Line drawing of the same lobbyLighting study of the lobby: downlight beams, wall washes and cove lines
Lighting layoutDownlight beamsWall washCove lighting
Structural frame
Core: stairs and lifts
Supply air ductwork
Riser shaft
Cold and hot water risers
Cable tray
Electrical riser
Pendant luminaires

Precision in Modeling.Reliability in Engineering

Electrical, mechanical and plumbing design assist, MEP drafting and Revit modeling, and calculations, for architects, developers, contractors and engineering firms.

MechanicalPlumbingElectricalLighting
Scroll

Looking for something?

Who we are

Engineering support that fits how your team already works

We work with architects, developers, contractors and engineering firms on the electrical, mechanical and plumbing side of their projects. You send drawings, markups or a Revit model, and we send back coordinated sheets, models and calculations that your engineer can check and issue.

Electrical covers power distribution, lighting and photometrics, low-voltage, solar PV and EV charging, designed to NEC, IECC and AS/NZS 3000. Mechanical covers heating and cooling loads, ducts and ventilation. Plumbing covers fixtures, water, drainage, vent and gas. MEP drafting and Revit modeling bring the three together in one coordinated model.

We work in your templates, to the codes of your region, and we catch conflicts in the model rather than on site.

How we work

One team for the model and the engineering

Models that are right before they leave our desk, and engineering your own engineer can check. Work with us on one or both.

The finished office buildingThe same building as a coordinated model with ducts, pipes, cable tray and luminairesThe buildingThe model

Precision in Modeling

MEP drafting and Revit models that coordinate, and sheets that come out of them cleanly: the structure, the ductwork, the pipes, the cable tray and the luminaires, checked against each other before anything is drawn.

MEP drafting
Revit and AutoCAD sheets from your markups
Revit modeling
Structure, MEP and lighting in your template
Coordination
Clash detection in Navisworks
As-built
Scan-to-BIM and survey models
Shop drawings
Fabrication-level detail
MEP drafting and Revit modeling
A calculator and handwritten notes on an engineer's deskThe calculation, written out

Reliability in Engineering

Design assist and permit drawings, with the calculations written out so your engineer can check every number.

Design assist
Layouts, schedules, permit sets
Calculations
Loads, sizing, voltage drop
Energy checks
COMcheck, Title 24, NCC Section J
Lighting
Photometrics in DIALux and AGi32
All services

Electrical, mechanical, plumbing

Three disciplines, one way of working: your templates, your standards, your engineer signs. Each has its own page, with what we offer in every region.

Electrical

Power, lighting, low-voltage, solar and EV charging.

  • Design assist and calculations
  • Lighting and photometrics
  • Panels, feeders and fire alarm
  • Revit and CAD support
Electrical in detail

Mechanical

Loads, ducts, ventilation and equipment.

  • Heating and cooling loads
  • Duct and ventilation sizing
  • Equipment schedules
  • Revit and CAD support
Mechanical in detail

Plumbing

Water, drainage, vent and gas.

  • Fixture counts and water sizing
  • Drainage, vent and gas sizing
  • Riser diagrams
  • Revit and CAD support
Plumbing in detail

Wherever the project is

The same templates and checks everywhere. The scope and the standards change by region, so each region has its own page.

Projects we are asked to do

Stores, restaurants, clinics, offices, homes, warehouses, and the solar and EV work that goes with them. Small and mid-size work is our normal.

  1. 01ResidentialHomes, townhouses and multifamily buildings
  2. 02Retail & shopping centersStores, boutiques and shopping centers
  3. 03Restaurants, cafés & barsKitchens, dining rooms, bars and breweries
  4. 04Hotels & hospitalitySmall hotels, motels and resorts
  5. 05HealthcareDental clinics, medical offices and facilities
  6. 06Education & communitySchools, daycares and community buildings
  7. 07Offices & workspacesFit-outs, tenant improvements and office buildings
  8. 08Commercial & mixed-useMixed-use buildings, gyms, salons and service stations
  9. 09Industrial, warehouses & labsWarehouses, distribution, manufacturing and laboratories
  10. 10Data centers & critical facilitiesPower chains, cooling and backup power
  11. 11Solar, EV charging & backup powerRooftop and carport PV, batteries, chargers and generators

How a project starts

No portal to learn. Send us the set, or book a short call first.

  1. Discovery and consultation

    A short conversation about the project, the deadline, the codes and what matters most to you. No obligation.

  2. Scope and onboarding

    You get a clear scope, timeline and price. We sign an NDA if you need one, set up secure file transfer and take on your Revit and CAD templates and layer standards.

  3. Engineering and modeling

    We do the design assist, calculations, drawings and Revit models, built to the codes of your region.

  4. Coordination and QA/QC

    We coordinate the trades in Navisworks and check the set against a QC list before it leaves us.

  5. Delivery and support

    You get clean, coordinated, permit-ready sheets on the agreed date, with quick turnaround on revisions.

Quality

Checks before anything leaves us

The same routine runs on every project, whatever its size, so a small job gets the same care as a large one.

A row of electricity meters and a distribution box on a pale brick wall
  • Standards set at the startCode editions, templates, layer standards and drawing conventions are written into a project sheet before work begins.
  • Calculations written outEvery load, sizing and voltage-drop calculation is documented, so your engineer can follow and check it.
  • Model checksClash detection and model health checks run before drawings are produced from the model.
  • A checklist for every sheetScales, labels, schedules, legends and the match between plans and schedules, checked sheet by sheet.
  • Reviewed by someone elseA second engineer reviews the set before it is issued to you.
  • Revisions on recordEvery change is logged against your comments, so nothing is lost between rounds.

How we work

The principles behind the team

  1. People firstWe look after the people who do the work and the partners we work with, and we build teams that last.
  2. Your data stays yoursFiles and models travel by secure transfer, stay on access-controlled storage and are used only for your project. We sign NDAs when you ask.
  3. Straight dealingWe say what we can do, give honest dates and tell you early when something changes.
  4. One team with yoursWe work in your templates and standards and talk directly to your engineers, so the work feels like part of your office.
  5. Turnaround you can plan aroundStreamlined Revit workflows and overlapping working hours keep revisions moving without cutting corners.
  6. Experienced eyes on every jobAn experienced engineer reviews each deliverable before it reaches you.

Client relationships

We do not just take on projects. We want to be the technical team you keep coming back to. We learn your standards, your preferences and how your firm likes to work, so each job goes faster than the last.

Team relationships

Our engineers work flexibly and are accountable for their own work. Trust inside the team is what makes on-time delivery routine, and it is why our clients deal with the same people from one project to the next.

Questions people ask first

What is MEP design assist?

MEP design assist is engineering support that works as an extension of your team: calculations, layouts, schedules and permit drawings for electrical, mechanical and plumbing, prepared in your templates for your licensed engineer to review and issue.

What does SYMATEQ do in each region?

SYMATEQ is a full MEP firm covering mechanical, electrical, plumbing, fire protection and fire alarm. In the US, we provide design assist for all five, with load and sizing calculations. In Canada, we provide MEP design assist with calculations. In Australia and New Zealand, we provide electrical design assist and calculations. In every region, we provide MEP drafting, Revit modeling and DIALux lighting models.

Do you offer MEP drafting and modeling?

Yes. We produce electrical, mechanical and plumbing drawings in Revit or AutoCAD and coordinated 3D Revit models with clash detection, as-built models and shop drawings, in your template, in every region we serve.

Can architects and contractors work with SYMATEQ directly?

Yes. SYMATEQ works directly with architects, general contractors, developers and engineering firms as their MEP, fire protection and fire alarm support partner. Each project starts with an agreed scope, schedule and fee. The project's licensed engineer reviews, seals and issues the final drawings.

Who reviews and seals the drawings?

Your licensed engineer. We prepare the drawings, models and calculations for them to review, seal and issue, and responsibility for the design stays with your firm.

What is MEP drafting and modeling?

MEP drafting produces the electrical, mechanical and plumbing drawings: plans, risers, schedules and details, in Revit or AutoCAD. MEP modeling builds the same systems as a coordinated 3D Revit model that the drawings and schedules come out of. We provide both, in your template, in every region.

What is the difference between engineering support and MEP drafting and modeling?

Engineering support is the design assist, calculations and layouts. MEP drafting and modeling is the Revit and CAD side: building the drawings and the model, coordinating the trades and producing sheets from it. You can work with us on either or both.

How quickly can you turn work around?

Markups and small revisions are typically back within one business day. Larger packages get a date from us before we start.

Which software and codes do you work in?

Revit, AutoCAD, Navisworks, DIALux, AGi32 and Bluebeam, to the code and edition your project is under.

Can we start with one small job?

Yes. Send one set and see how it goes before you decide on anything bigger.

Start a project

Have a project in mind?

Tell us the discipline, the code and the deadline. We reply with a price and a date, usually within one business day.

Used only to reply to you. Privacy